Tom's Guide > Forum > Wireless Networking > Setup, Configuration & Security > 2 wireless routers 1 modem

2 wireless routers 1 modem

Forum Wireless Networking : Setup, Configuration & Security - 2 wireless routers 1 modem

TomsGuide.com: Over 800,000 questions and answers to address all your high-tech questions. Sign up now! Its free!
Ask the community Add a reply
Word :    Username :           
 
snooze2   09-10-2006 at 02:12:59 AM

allright this may seem like an odd question but is there a way to use two wireless routers to have 2 networks in my house. I have a cable modem and one netgear 108mbps router and one old linksys 11mbps router. I want two seperate wireless networks because the linksys was allways up and the netgear resets every once and awhile. My parents are connected to AOL all the time so this is a big problem for them cause they keep losing connection. I'm fine with it reseting for the better range/speed of the netgear.

Thanks for anyhelp

Add a reply
Sponsored Links
Register or log in to remove.
the_taker   09-11-2006 at 02:50:08 AM
- 0 +

My guess is that cost is probably your main issue as far as why you don't just replace them with a new, single router. That would be by far, the best way to go for your situation.

1. If your ISP offers 2 dynamic IP addresses (i know Time Warner does, and i think it might be common for most cable company ISP's) then you could connect a switch to the cable modem (note: plugging 2 computers in this way is a good way to test to see if they both get an IP address) and then plug both wireless routers into the switch. Benefit: no double NAT-ing, or "misfires" of internet request returns.

No matter what you do, make sure that you set the Wireless Channel at least 2 channels (1 & 3, etc) apart from each other, but make sure that you don't set your channel the same as any other nearby networks for either router.

2. If you only have 1 IP from your ISP (usually DSL or long-range wireless providers), then plug in the reliable router to the modem/DSL router first, then the faster/less reliable router second. Same channel rules still apple so they don't interfere. You would need to make sure that whatever Subnet (not subnet mask) the 1st router uses doesn't match the second.

Example:

1st router:
-WAN/Uplink/Internet port plugged into modem/DSL router
-LAN port/wireless as follows
Internal IP: 192.168.0.1
subnet mask: 255.255.255.0
DHCP pool: 192.168.0.50 to .254

2nd router:
-Wan uplink port into LAN port of 1st router
-LAN port/wireless as follows
Interla IP: 192.168.1.1
subnet mask 255.255.255.0
DHCP pool: 192.168.1.50 to .254


in this way, the subnets are different, double-NAT isn't usually an issue.

Good luck!

Reply to the_taker
blue68f100   09-11-2006 at 03:48:48 AM
- 0 +

Yes you can. It's done regulary for people with 11b hardware and 11g hardware. This way 11g can use the WPA while the 11b uses WEP.

You can have one router feed the other:
modem to 11brouter WAN > 11brouter LAN to 11gRouter WAN. You can turn off the NAT on the second router. Or leave it active for more security.

Reply to blue68f100
Ask the community Add a reply
Tom's Guide > Forum > Wireless Networking > Setup, Configuration & Security > 2 wireless routers 1 modem
Go to:

There are 12 identified and unidentified users. To see the list of identified users, Click here.

Forum map
Bestofmedia Forum ©
2000-2009 Bestofmedia Group
Page generated in 0.284 seconds
Please mind

You are about to answer a thread that has been inactive for more than 6 months.
If you still wish to proceed, please ensure that your posting is original and does not duplicate or overlap any prior responses to this thread.

Add a reply Cancel
Google ads