Using a Linksys router as an access point

Archived from groups: (More info?)

Hi,
I have two wireless routers. One is connected as normal, but I want to
extend my range with the other one (i.e. turn it into an access point).
How do I do it (please tell it step by step, as I have noooo idea at
this point)? Do I have to set up a static IP address? The product says
it is capable of being a wireless access point, but the Linksys website
doesn't tell you how to set it up. Some websites say that I have to
have the access point plugged into an ethernet cable in order to get
the wireless access point...this kind of defeats the purpose.

Thanks in advance.

Archived from groups: (More info?)

On 26 Sep 2005 19:45:25 -0700, bwadamson@gmail.com wrote:

>I have two wireless routers.

Model numbers please?
Hardware version also.
If WRT54G and alternative firmware, name and version.

> One is connected as normal,

I'll assume that "normal" means setup as a DSL or cable modem router.

>but I want to
>extend my range with the other one (i.e. turn it into an access point).

Easy but I don't think that's what you really want to do. See below.

>How do I do it (please tell it step by step, as I have noooo idea at
>this point)? Do I have to set up a static IP address? The product says
>it is capable of being a wireless access point, but the Linksys website
>doesn't tell you how to set it up. Some websites say that I have to
>have the access point plugged into an ethernet cable in order to get
>the wireless access point...this kind of defeats the purpose.

Oh-oh. I presume that you're trying to setup the 2nd router as a WDS
repeater. It's not clear, but I read between the lines that you do
NOT wish to run a cable between the two boxes. If your mystery
Linksys routers are WRT54G this can be done using WDS. Instructions:

http://www.linksysinfo.org/modules [...] page&pid=7

If you DO want to run a cable, and don't want to deal with WDS, or
your mystery Linksys router is not a WRT54G, then you can setup the
2nd router as an access point by:
1. Change the IP address of the 2nd router to 192.168.1.2. The idea
is to not duplicate the IP address of the first router.
2. Optionally set the SSID and encryption keys to the same on both
routers.
3. Ignore the WAN port. The WAN port is not used.
4. Turn OFF the DHCP server on the 2nd router.
5. Connect a cable between one LAN port on the first router, to a LAN
port on the 2nd router. You may need a crossover cable. Make sure
the front panel light are correct for the ports when you plug in the
cable.



--
Jeff Liebermann jeffl@comix.santa-cruz.ca.us
150 Felker St #D http://www.LearnByDestroying.com
Santa Cruz CA 95060 http://802.11junk.com
Skype: JeffLiebermann AE6KS 831-336-2558

Archived from groups: (More info?)

On Wed, 28 Sep 2005 13:59:33 GMT, "DanR" <dhr22@sorrynospm.com> wrote:

>Jeff, you say "may need a crossover cable". When and when not do you need a
>crossover cable for this type setup?

Reading between your lines, I deduce that you do want to use a cable
to connect the two routers instead of WDS.

When going from an ethernet switch to another ethernet switch, one
*USUALLY* needs a cross-over ethernet cable. Same with going between
two computers. However, modern routers and switches all have an extra
crossover connector, an MDI/MDI-X switch, or automagic polarity
switching. I vaguely recall (not sure) that the WRT54G has automagic
polarity sensing and therefore does NOT require a crossover cable.

> Might one not know until inspecting the
>"front panel light"?

Yes. The easy way to tell for sure is to just insert an ordinary
ethernet CAT5 cable between the LAN ports on both WRT54G boxes. If
the front panel light turn on in the normal manner, you win and it
will work. If the front panel light stay off, you need a crossover
cable or adapter.

Incidentally, I sometime use this trick to test my ethernet cables.
One end of the cable goes to the crossover connector on the switch.
The other goes to any of the other jacks. If the lights come on, it's
wired correctly. Unfortunately, it doesn't check for split pairs and
flakey connections, but if I'm too lazy to dig out the cable tester,
this test will do.

I would not buy a long crossover cable. I build an adapter using a
cheap ($2) RJ45 jack, a short length of CAT5, and an RJ45 plug. The
RJ45 jack is wired for normal EIA-568B. The plug gets the creative
crossover wiring plan. With this adapter, I can take any ordinary
ethernet cable and convert it into a crossover cable.

--
Jeff Liebermann jeffl@comix.santa-cruz.ca.us
150 Felker St #D http://www.LearnByDestroying.com
Santa Cruz CA 95060 http://802.11junk.com
Skype: JeffLiebermann AE6KS 831-336-2558

Same problem here.
I have a WRT54GC as primary Router and a WRT54GS that I want to make it work as a repeater to increase the range of my wireless network but I do not want to connect the routers by cable.
Can someone help me?

Wireless bridging seems to fit the bill for those not wanting to run an Cat-5 cable 200'.

This

combined with

this

should help those that want to extend their wireless network without using cables. Also dd-wrt also has its own wiki site so you won't need to flood their forums.