Can one router be conencted to another

Archived from groups: alt.internet.wireless (More info?)

I have a 7004VWBR SMC Barricade with a print server built in.
I like the print server. The router itself is quite old and lacks
some key features. SSID broadcast cannot be disabled, nor WPA, bad
user interface. However the router itself is quite solid in
performance--no need for reboots etc.

I have a Netgear MR 814 sitting around which is a a newer model, from
what I have seen it has a better interface. I would like to find out
if it is possible to use this as a main router and use the SMC simply
as a print server. In which case do I connect the WAN port to one of
the Netgear's ports? Or is this not possible?

I would prefer not to buy another print server, since I already have
one.

Archived from groups: alt.internet.wireless (More info?)

Doug Jamal <bishiv6AT@yahooDOT.com> wrote in message news:<N3wmd.25984$6w6.23185@tornado.tampabay.rr.com>...
> Yes, you can use one router in conjunction with another. You will have
> to make the SMC Barricade your access point (AP). Connect an ethernet
> cable from one of the LAN ports of the SMC Barricade to one of the LAN
> ports of the MR814. Plug another ethernet cable from the DSL/Cable
> modem to the WAN port of the MR814. Enable the DHCP server of the MR814
> and disable the DHCP server of the SMC Barricade. Give both routers an
> IP address within the same subnet. For example: Give the MR814 an IP
> address of 192.168.0.100 and give the Barricade a IP address of
> 192.168.0.200. Personally, I'd change the entire IP address to
> something like 10.65.100.1, however, some routers won't allow you to do
> that. Unless you're planning on using the wireless radio in both
> routers, then disable the wireless feature of the MR814. There you have
> it. Take care.

Actually I want to use the wireless of the MR814. So are the
instructions still the same?

>
> Vijay Kumar wrote:
> > I have a 7004VWBR SMC Barricade with a print server built in.
> > I like the print server. The router itself is quite old and lacks
> > some key features. SSID broadcast cannot be disabled, nor WPA, bad
> > user interface. However the router itself is quite solid in
> > performance--no need for reboots etc.
> >
> > I have a Netgear MR 814 sitting around which is a a newer model, from
> > what I have seen it has a better interface. I would like to find out
> > if it is possible to use this as a main router and use the SMC simply
> > as a print server. In which case do I connect the WAN port to one of
> > the Netgear's ports? Or is this not possible?
> >
> > I would prefer not to buy another print server, since I already have
> > one.

Archived from groups: alt.internet.wireless (More info?)

Doug Jamal wrote:
> Connect an ethernet
> cable from one of the LAN ports of the SMC Barricade to one of the LAN
> ports of the MR814.

For the above either:
use an ordinary ethernet port on each router and
a crossover cable,
or
use a straight through ethernet cable connected to an ordinary
port on one router and an uplink port on the other router.

wk

Archived from groups: alt.internet.wireless (More info?)

On Wed, 17 Nov 2004 11:27:32 -0500, in alt.internet.wireless , wk
<wk-news17@sunlight.ca> wrote:

> use an ordinary ethernet port on each router and
> a crossover cable,

you almost certainly don't need a X-over cable - I'm not aware that anyone
still makes switches that don't autosense. Hubs yes, switches no.

--
Mark McIntyre
CLC FAQ <http://www.eskimo.com/~scs/C-faq/top.html>
CLC readme: <http://www.ungerhu.com/jxh/clc.welcome.txt>

----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups
----= East and West-Coast Server Farms - Total Privacy via Encryption =----