Archived from groups: microsoft.public.windowsxp.basics (More info?)

Help please - I'm going round in ever-diminishing circles here, almost
disappearing up my fundamental you-know-what
..
My PC had 6 USB1 ports - I upgraded by adding a 2-port USB2 card, with a
USB2 4 port hub ... When I had XP Home, all was fine. I then crashed my
hdd, so bit the bullet, got a new drive, and XP Pro and started again.

The (Via) USB2 card was bought new, as was the 4 port hub - I have the
driver CD for the card.

According to System Manager, everything's fine, working correctly. BUT -
every time I try to use my USB2 memory stick in one of the 4 ports on the
hub, it comes up with "This would work faster with USB2 - put it in one of
the 4 unused ports" .... which is unmitigated b/s as it's already IN one of
them - changing makes no difference.

I've already outed the 4 port hub in the belief it MIGHT be duff, got
replacement - beggars belief that 2 sealed units are both u/s. Hub has
external power, so it's not that either. It's driving me nuts - HELP !!!!

Archived from groups: microsoft.public.windowsxp.basics (More info?)

When you reinstalled XP Pro did you install the chipset drivers for the
motherboard and the drivers for the add-in card?

"Yabbadoo" <nospam@thank.you> wrote in message
news:gebDe.1291$Cu3.608@newsfe4-win.ntli.net...
> Help please - I'm going round in ever-diminishing circles here, almost
> disappearing up my fundamental you-know-what
> .
> My PC had 6 USB1 ports - I upgraded by adding a 2-port USB2 card, with a
> USB2 4 port hub ... When I had XP Home, all was fine. I then crashed my
> hdd, so bit the bullet, got a new drive, and XP Pro and started again.
>
> The (Via) USB2 card was bought new, as was the 4 port hub - I have the
> driver CD for the card.
>
> According to System Manager, everything's fine, working correctly. BUT -
> every time I try to use my USB2 memory stick in one of the 4 ports on the
> hub, it comes up with "This would work faster with USB2 - put it in one of
> the 4 unused ports" .... which is unmitigated b/s as it's already IN one
> of them - changing makes no difference.
>
> I've already outed the 4 port hub in the belief it MIGHT be duff, got
> replacement - beggars belief that 2 sealed units are both u/s. Hub has
> external power, so it's not that either. It's driving me nuts - HELP !!!!
>

Archived from groups: microsoft.public.windowsxp.basics (More info?)

Not sure what you mean about chipset drivers, but as stated I have (and
used) the USB2 card installation CD.
According to every diagnostic (System Manager, Belarc and Everest) there's
no probs, every device is functionng normally. Also, I auto-update (SP2
installed months ago, and all later updates as released).

I have a totally clean system, defended by AVG, MS antispyware latest beta,
Spybot, Adaware, and daily clean/defrag by Tune-up Utilities schedule. I run
total manual scans at least weekly, so, it ain't malware.

PC is working fine on all apps/hardware - except USB2. Just installed new
DVD_RW to replace DVD_R - that too working just fine.

"Jerry" <NoSpamChiefZeke@MSN.com> wrote in message
news:uOr9c7IjFHA.3656@TK2MSFTNGP09.phx.gbl...
> When you reinstalled XP Pro did you install the chipset drivers for the
> motherboard and the drivers for the add-in card?
>
> "Yabbadoo" <nospam@thank.you> wrote in message
> news:gebDe.1291$Cu3.608@newsfe4-win.ntli.net...
>> Help please - I'm going round in ever-diminishing circles here, almost
>> disappearing up my fundamental you-know-what
>> .
>> My PC had 6 USB1 ports - I upgraded by adding a 2-port USB2 card, with a
>> USB2 4 port hub ... When I had XP Home, all was fine. I then crashed my
>> hdd, so bit the bullet, got a new drive, and XP Pro and started again.
>>
>> The (Via) USB2 card was bought new, as was the 4 port hub - I have the
>> driver CD for the card.
>>
>> According to System Manager, everything's fine, working correctly. BUT -
>> every time I try to use my USB2 memory stick in one of the 4 ports on the
>> hub, it comes up with "This would work faster with USB2 - put it in one
>> of the 4 unused ports" .... which is unmitigated b/s as it's already IN
>> one of them - changing makes no difference.
>>
>> I've already outed the 4 port hub in the belief it MIGHT be duff, got
>> replacement - beggars belief that 2 sealed units are both u/s. Hub has
>> external power, so it's not that either. It's driving me nuts - HELP
>> !!!!
>>
>
>

Archived from groups: microsoft.public.windowsxp.basics (More info?)

Look under bus adapters in Belarc Advisor. Do you have an entry for
"Standard Enhanced PCI to USB Host Controller" or, in my case "Adaptec
AUA-3121 PCI to USB Enhanced Host Controller

--
Regards,

Richard Urban
Microsoft MVP Windows Shell/User

Quote from: George Ankner
"If you knew as much as you thought you know,
You would realize that you don't know what you thought you knew!"

"Yabbadoo" <nospam@thank.you> wrote in message
news:ApdDe.3087$yH4.2017@newsfe2-win.ntli.net...
> Not sure what you mean about chipset drivers, but as stated I have (and
> used) the USB2 card installation CD.
> According to every diagnostic (System Manager, Belarc and Everest) there's
> no probs, every device is functionng normally. Also, I auto-update (SP2
> installed months ago, and all later updates as released).
>
> I have a totally clean system, defended by AVG, MS antispyware latest
> beta, Spybot, Adaware, and daily clean/defrag by Tune-up Utilities
> schedule. I run total manual scans at least weekly, so, it ain't malware.
>
> PC is working fine on all apps/hardware - except USB2. Just installed new
> DVD_RW to replace DVD_R - that too working just fine.
>
> "Jerry" <NoSpamChiefZeke@MSN.com> wrote in message
> news:uOr9c7IjFHA.3656@TK2MSFTNGP09.phx.gbl...
>> When you reinstalled XP Pro did you install the chipset drivers for the
>> motherboard and the drivers for the add-in card?
>>
>> "Yabbadoo" <nospam@thank.you> wrote in message
>> news:gebDe.1291$Cu3.608@newsfe4-win.ntli.net...
>>> Help please - I'm going round in ever-diminishing circles here, almost
>>> disappearing up my fundamental you-know-what
>>> .
>>> My PC had 6 USB1 ports - I upgraded by adding a 2-port USB2 card, with a
>>> USB2 4 port hub ... When I had XP Home, all was fine. I then crashed my
>>> hdd, so bit the bullet, got a new drive, and XP Pro and started again.
>>>
>>> The (Via) USB2 card was bought new, as was the 4 port hub - I have the
>>> driver CD for the card.
>>>
>>> According to System Manager, everything's fine, working correctly.
>>> BUT - every time I try to use my USB2 memory stick in one of the 4
>>> ports on the hub, it comes up with "This would work faster with USB2 -
>>> put it in one of the 4 unused ports" .... which is unmitigated b/s as
>>> it's already IN one of them - changing makes no difference.
>>>
>>> I've already outed the 4 port hub in the belief it MIGHT be duff, got
>>> replacement - beggars belief that 2 sealed units are both u/s. Hub has
>>> external power, so it's not that either. It's driving me nuts - HELP
>>> !!!!
>>>
>>
>>
>
>

Archived from groups: microsoft.public.windowsxp.basics (More info?)

Chipset drivers are the drivers for the motherboard. Although you're using a
separate card, it could still be related to not having the correct chipset
drivers because those drivers affect things that are plugged into the
motherboard -- like that usb card.


"Yabbadoo" <nospam@thank.you> wrote in message
news:ApdDe.3087$yH4.2017@newsfe2-win.ntli.net...
> Not sure what you mean about chipset drivers, but as stated I have (and
> used) the USB2 card installation CD.
> According to every diagnostic (System Manager, Belarc and Everest) there's
> no probs, every device is functionng normally. Also, I auto-update (SP2
> installed months ago, and all later updates as released).
>
> I have a totally clean system, defended by AVG, MS antispyware latest
> beta, Spybot, Adaware, and daily clean/defrag by Tune-up Utilities
> schedule. I run total manual scans at least weekly, so, it ain't malware.
>
> PC is working fine on all apps/hardware - except USB2. Just installed new
> DVD_RW to replace DVD_R - that too working just fine.
>
> "Jerry" <NoSpamChiefZeke@MSN.com> wrote in message
> news:uOr9c7IjFHA.3656@TK2MSFTNGP09.phx.gbl...
>> When you reinstalled XP Pro did you install the chipset drivers for the
>> motherboard and the drivers for the add-in card?
>>
>> "Yabbadoo" <nospam@thank.you> wrote in message
>> news:gebDe.1291$Cu3.608@newsfe4-win.ntli.net...
>>> Help please - I'm going round in ever-diminishing circles here, almost
>>> disappearing up my fundamental you-know-what
>>> .
>>> My PC had 6 USB1 ports - I upgraded by adding a 2-port USB2 card, with a
>>> USB2 4 port hub ... When I had XP Home, all was fine. I then crashed my
>>> hdd, so bit the bullet, got a new drive, and XP Pro and started again.
>>>
>>> The (Via) USB2 card was bought new, as was the 4 port hub - I have the
>>> driver CD for the card.
>>>
>>> According to System Manager, everything's fine, working correctly.
>>> BUT - every time I try to use my USB2 memory stick in one of the 4
>>> ports on the hub, it comes up with "This would work faster with USB2 -
>>> put it in one of the 4 unused ports" .... which is unmitigated b/s as
>>> it's already IN one of them - changing makes no difference.
>>>
>>> I've already outed the 4 port hub in the belief it MIGHT be duff, got
>>> replacement - beggars belief that 2 sealed units are both u/s. Hub has
>>> external power, so it's not that either. It's driving me nuts - HELP
>>> !!!!
>>>
>>
>>
>
>

Archived from groups: microsoft.public.windowsxp.basics (More info?)

All motherboards require reinstallation of the mobo chipset drivers after a
new installation of Windows. It is like needing to reinstall your video
card drivers. The usb2 card drivers on your cd are for versions of Windows
prior to XP SP1. They make no difference to XP SP1 and later because they
are built into the OS from SP1 on. Find the cd with that came with the mobo
or visit the manufacturer's site and download the drivers and install them.
There should be some useful utilities also.

"Yabbadoo" <nospam@thank.you> wrote in message
news:ApdDe.3087$yH4.2017@newsfe2-win.ntli.net...
> Not sure what you mean about chipset drivers, but as stated I have (and
> used) the USB2 card installation CD.
> According to every diagnostic (System Manager, Belarc and Everest) there's
> no probs, every device is functionng normally. Also, I auto-update (SP2
> installed months ago, and all later updates as released).
>
> I have a totally clean system, defended by AVG, MS antispyware latest
> beta, Spybot, Adaware, and daily clean/defrag by Tune-up Utilities
> schedule. I run total manual scans at least weekly, so, it ain't malware.
>
> PC is working fine on all apps/hardware - except USB2. Just installed new
> DVD_RW to replace DVD_R - that too working just fine.
>
> "Jerry" <NoSpamChiefZeke@MSN.com> wrote in message
> news:uOr9c7IjFHA.3656@TK2MSFTNGP09.phx.gbl...
>> When you reinstalled XP Pro did you install the chipset drivers for the
>> motherboard and the drivers for the add-in card?
>>
>> "Yabbadoo" <nospam@thank.you> wrote in message
>> news:gebDe.1291$Cu3.608@newsfe4-win.ntli.net...
>>> Help please - I'm going round in ever-diminishing circles here, almost
>>> disappearing up my fundamental you-know-what
>>> .
>>> My PC had 6 USB1 ports - I upgraded by adding a 2-port USB2 card, with a
>>> USB2 4 port hub ... When I had XP Home, all was fine. I then crashed my
>>> hdd, so bit the bullet, got a new drive, and XP Pro and started again.
>>>
>>> The (Via) USB2 card was bought new, as was the 4 port hub - I have the
>>> driver CD for the card.
>>>
>>> According to System Manager, everything's fine, working correctly.
>>> BUT - every time I try to use my USB2 memory stick in one of the 4
>>> ports on the hub, it comes up with "This would work faster with USB2 -
>>> put it in one of the 4 unused ports" .... which is unmitigated b/s as
>>> it's already IN one of them - changing makes no difference.
>>>
>>> I've already outed the 4 port hub in the belief it MIGHT be duff, got
>>> replacement - beggars belief that 2 sealed units are both u/s. Hub has
>>> external power, so it's not that either. It's driving me nuts - HELP
>>> !!!!
>>>
>>
>>
>
>

Archived from groups: microsoft.public.windowsxp.basics (More info?)

Here's a cut/paste of relevant Belarc report covering all USB bits.
I'm a bit unsure about why there should be 2 "Host Companion" and 3
"Via Rev 5 UHC's" - these all relate to on-board USB1, though why there
should be so many, I don't know.
As set up right now - have USB controller for Logitech mouse and /k/b,
4 rear and 2 front USB1 ports (only 1 in use for the radio mouse/kb
controller) and the USB2 card plugged in but not in use. No printer, scanner
or other device connected.

Does this give you help in solving my problem?

Sincerely, Len






Standard floppy disk controller
Primary IDE Channel [Controller]
Secondary IDE Channel [Controller]
VIA Bus Master IDE Controller NVIDIA GeForce2 MX/MX 400 (Microsoft
Corporation) [Display adapter]
Samsung SyncMaster [Monitor] (17.1"vis, s/n H4JW907504, October 2003)
Bus Adapters Multimedia
A347SCSI SCSI Controller
VIA Rev 5 or later USB Universal Host Companion Controller
VIA Rev 5 or later USB Universal Host Companion Controller
VIA Rev 5 or later USB Universal Host Controller
VIA Rev 5 or later USB Universal Host Controller
VIA Rev 5 or later USB Universal Host Controller
VIA USB 2.0 Enhanced Host Controller Creative Game Port
Creative SB Audigy LS
Communications Other Devices
LNE100TX Fast Ethernet Adapter Version 1.0
Realtek RTL8139/810x Family Fast Ethernet NIC
Network Card MAC Address: 00:A0:CC:2E:40:1F
Network IP Address: 81.99.84.92 / 24 HID-compliant consumer control
device
HID-compliant consumer control device
HID-compliant device
USB Human Interface Device
USB Human Interface Device
HID Keyboard Device
Standard 101/102-Key or Microsoft Natural PS/2 Keyboard
HID-compliant mouse
USB Composite Device
USB Root Hub
USB Root Hub
USB Root Hub
USB Root Hub
USB Root Hub
USB Root Hub

"Richard Urban [MVP]" <richardurbanREMOVETHIS@hotmail.com> wrote in message
newsdGjnnKjFHA.4000@TK2MSFTNGP12.phx.gbl...
> Look under bus adapters in Belarc Advisor. Do you have an entry for
> "Standard Enhanced PCI to USB Host Controller" or, in my case "Adaptec
> AUA-3121 PCI to USB Enhanced Host Controller
>
> --
> Regards,
>
> Richard Urban
> Microsoft MVP Windows Shell/User
>
> Quote from: George Ankner
> "If you knew as much as you thought you know,
> You would realize that you don't know what you thought you knew!"
>
> "Yabbadoo" <nospam@thank.you> wrote in message
> news:ApdDe.3087$yH4.2017@newsfe2-win.ntli.net...
>> Not sure what you mean about chipset drivers, but as stated I have (and
>> used) the USB2 card installation CD.
>> According to every diagnostic (System Manager, Belarc and Everest)
>> there's no probs, every device is functionng normally. Also, I
>> auto-update (SP2 installed months ago, and all later updates as
>> released).
>>
>> I have a totally clean system, defended by AVG, MS antispyware latest
>> beta, Spybot, Adaware, and daily clean/defrag by Tune-up Utilities
>> schedule. I run total manual scans at least weekly, so, it ain't malware.
>>
>> PC is working fine on all apps/hardware - except USB2. Just installed new
>> DVD_RW to replace DVD_R - that too working just fine.
>>
>> "Jerry" <NoSpamChiefZeke@MSN.com> wrote in message
>> news:uOr9c7IjFHA.3656@TK2MSFTNGP09.phx.gbl...
>>> When you reinstalled XP Pro did you install the chipset drivers for the
>>> motherboard and the drivers for the add-in card?
>>>
>>> "Yabbadoo" <nospam@thank.you> wrote in message
>>> news:gebDe.1291$Cu3.608@newsfe4-win.ntli.net...
>>>> Help please - I'm going round in ever-diminishing circles here, almost
>>>> disappearing up my fundamental you-know-what
>>>> .
>>>> My PC had 6 USB1 ports - I upgraded by adding a 2-port USB2 card, with
>>>> a USB2 4 port hub ... When I had XP Home, all was fine. I then crashed
>>>> my hdd, so bit the bullet, got a new drive, and XP Pro and started
>>>> again.
>>>>
>>>> The (Via) USB2 card was bought new, as was the 4 port hub - I have the
>>>> driver CD for the card.
>>>>
>>>> According to System Manager, everything's fine, working correctly.
>>>> BUT - every time I try to use my USB2 memory stick in one of the 4
>>>> ports on the hub, it comes up with "This would work faster with USB2 -
>>>> put it in one of the 4 unused ports" .... which is unmitigated b/s as
>>>> it's already IN one of them - changing makes no difference.
>>>>
>>>> I've already outed the 4 port hub in the belief it MIGHT be duff, got
>>>> replacement - beggars belief that 2 sealed units are both u/s. Hub has
>>>> external power, so it's not that either. It's driving me nuts - HELP
>>>> !!!!
>>>>
>>>
>>>
>>
>>
>
>

Archived from groups: microsoft.public.windowsxp.basics (More info?)

If only ...
http://usa.asus.com/aap/a7v266e-aa/overview.htm

is the link to the Asus site, A7V266E rev 1.xx m/b, BUT the manual/chipset
download page is "not available". Googling hasn't yielded any other source,
unless I mis-read it.

I'm treading in virgin territory here - areas of expertise I'm not confident
of - so forgive me if I'm going OT -
I remember a while back, updating BIOS - ACPI Bios rev 1006 1/23/2002
installed. Is that relevant ?

FWIW - though upgraded since, this pc started out as a pre-installed XPHome
commercial kit (Athlon 1.533Ghz on Asus m/b). The original m/b and processor
are about all that's left - added memory, both optical drives changed,
original hdd is now "slave" to a new hdd, XPPro replaces XPHome, sound card
added, USB2 card added, 2 LAN cards .... I still have the original set-up
CD's but the "Drivers" sections only relate to NVidea graphics and CMAudio
sound - no trace of Asus A7V266E m/b or chipset drivers whatsoever. They
could be in the "Setup.exe" file itself, but I'm unwilling to run that,
given 3 years+ upgrades since, with no probs except this one.

Can you help further, please?


"D.Currie" <dmbcurrie.nospam@hotmail.com> wrote in message
news:3k5vjdFsnennU1@individual.net...
> Chipset drivers are the drivers for the motherboard. Although you're using
> a separate card, it could still be related to not having the correct
> chipset drivers because those drivers affect things that are plugged into
> the motherboard -- like that usb card.
>
>
> "Yabbadoo" <nospam@thank.you> wrote in message
> news:ApdDe.3087$yH4.2017@newsfe2-win.ntli.net...
>> Not sure what you mean about chipset drivers, but as stated I have (and
>> used) the USB2 card installation CD.
>> According to every diagnostic (System Manager, Belarc and Everest)
>> there's no probs, every device is functionng normally. Also, I
>> auto-update (SP2 installed months ago, and all later updates as
>> released).
>>
>> I have a totally clean system, defended by AVG, MS antispyware latest
>> beta, Spybot, Adaware, and daily clean/defrag by Tune-up Utilities
>> schedule. I run total manual scans at least weekly, so, it ain't malware.
>>
>> PC is working fine on all apps/hardware - except USB2. Just installed new
>> DVD_RW to replace DVD_R - that too working just fine.
>>
>> "Jerry" <NoSpamChiefZeke@MSN.com> wrote in message
>> news:uOr9c7IjFHA.3656@TK2MSFTNGP09.phx.gbl...
>>> When you reinstalled XP Pro did you install the chipset drivers for the
>>> motherboard and the drivers for the add-in card?
>>>
>>> "Yabbadoo" <nospam@thank.you> wrote in message
>>> news:gebDe.1291$Cu3.608@newsfe4-win.ntli.net...
>>>> Help please - I'm going round in ever-diminishing circles here, almost
>>>> disappearing up my fundamental you-know-what
>>>> .
>>>> My PC had 6 USB1 ports - I upgraded by adding a 2-port USB2 card, with
>>>> a USB2 4 port hub ... When I had XP Home, all was fine. I then crashed
>>>> my hdd, so bit the bullet, got a new drive, and XP Pro and started
>>>> again.
>>>>
>>>> The (Via) USB2 card was bought new, as was the 4 port hub - I have the
>>>> driver CD for the card.
>>>>
>>>> According to System Manager, everything's fine, working correctly.
>>>> BUT - every time I try to use my USB2 memory stick in one of the 4
>>>> ports on the hub, it comes up with "This would work faster with USB2 -
>>>> put it in one of the 4 unused ports" .... which is unmitigated b/s as
>>>> it's already IN one of them - changing makes no difference.
>>>>
>>>> I've already outed the 4 port hub in the belief it MIGHT be duff, got
>>>> replacement - beggars belief that 2 sealed units are both u/s. Hub has
>>>> external power, so it's not that either. It's driving me nuts - HELP
>>>> !!!!
>>>>
>>>
>>>
>>
>>
>
>

Archived from groups: microsoft.public.windowsxp.basics (More info?)

Since replying to last message, have found an ASUS VIA DDR chipset series
"support" CD (in addition to the TARGA pc support CD) both of wh came with
the original PC, some 3 + years ago. Have thoroughly searched this CD too -
no mb manual, nothing relating to USB or chipset drivers
Further - this PC (with XPHome pre-installed), but - not one of the support
files on any of the CD's mention XP - all the drivers pre-date XP (are for
W98 up to NT or 2000) so I would be reluctant to use these CD's as source
for XPPro drivers.
As far ASUS support is concerned - can get to the site via link
http://usa.asus.com/aap/a7v266e-aa/overview.htm but that's as far as it
goes - the overview only, further pages/downloads are just "not available"
This actually replicates situation a year or more ago - had probs with the
on-board CMI8738 sound, ASUS site then operated but was useless as far as
updated drivers were concerned, none worked. Solved that prob by installing
new sound card. Given both previous and current history, next time I
upgrade it will not be an Asus m/b! I recall various forums discussing
identical probs - all equally frustrated.

Appreciate the advice, but alas! it's no good for Asus m/b's.


"Colin Barnhorst" <colinbarharst@msn.com> wrote in message
news:uPToIpOjFHA.1044@tk2msftngp13.phx.gbl...
> All motherboards require reinstallation of the mobo chipset drivers after
> a new installation of Windows. It is like needing to reinstall your video
> card drivers. The usb2 card drivers on your cd are for versions of
> Windows prior to XP SP1. They make no difference to XP SP1 and later
> because they are built into the OS from SP1 on. Find the cd with that
> came with the mobo or visit the manufacturer's site and download the
> drivers and install them. There should be some useful utilities also.
>
> "Yabbadoo" <nospam@thank.you> wrote in message
> news:ApdDe.3087$yH4.2017@newsfe2-win.ntli.net...
>> Not sure what you mean about chipset drivers, but as stated I have (and
>> used) the USB2 card installation CD.
>> According to every diagnostic (System Manager, Belarc and Everest)
>> there's no probs, every device is functionng normally. Also, I
>> auto-update (SP2 installed months ago, and all later updates as
>> released).
>>
>> I have a totally clean system, defended by AVG, MS antispyware latest
>> beta, Spybot, Adaware, and daily clean/defrag by Tune-up Utilities
>> schedule. I run total manual scans at least weekly, so, it ain't malware.
>>
>> PC is working fine on all apps/hardware - except USB2. Just installed new
>> DVD_RW to replace DVD_R - that too working just fine.
>>
>> "Jerry" <NoSpamChiefZeke@MSN.com> wrote in message
>> news:uOr9c7IjFHA.3656@TK2MSFTNGP09.phx.gbl...
>>> When you reinstalled XP Pro did you install the chipset drivers for the
>>> motherboard and the drivers for the add-in card?
>>>
>>> "Yabbadoo" <nospam@thank.you> wrote in message
>>> news:gebDe.1291$Cu3.608@newsfe4-win.ntli.net...
>>>> Help please - I'm going round in ever-diminishing circles here, almost
>>>> disappearing up my fundamental you-know-what
>>>> .
>>>> My PC had 6 USB1 ports - I upgraded by adding a 2-port USB2 card, with
>>>> a USB2 4 port hub ... When I had XP Home, all was fine. I then crashed
>>>> my hdd, so bit the bullet, got a new drive, and XP Pro and started
>>>> again.
>>>>
>>>> The (Via) USB2 card was bought new, as was the 4 port hub - I have the
>>>> driver CD for the card.
>>>>
>>>> According to System Manager, everything's fine, working correctly.
>>>> BUT - every time I try to use my USB2 memory stick in one of the 4
>>>> ports on the hub, it comes up with "This would work faster with USB2 -
>>>> put it in one of the 4 unused ports" .... which is unmitigated b/s as
>>>> it's already IN one of them - changing makes no difference.
>>>>
>>>> I've already outed the 4 port hub in the belief it MIGHT be duff, got
>>>> replacement - beggars belief that 2 sealed units are both u/s. Hub has
>>>> external power, so it's not that either. It's driving me nuts - HELP
>>>> !!!!
>>>>
>>>
>>>
>>
>>
>
>

Archived from groups: microsoft.public.windowsxp.basics (More info?)

Could you have reached that point where you should take your computer to a
professional and allow them to straighten it out for you?

I have one computer that uses an Asus A7V266E M/B. The M/B came with
everything necessary to set up the computer, up to Windows 2000. Windows XP
came out after the M/B was introduced. Of course you won't find what you
need on the CD. You have to go to the various manufacturers web sites and
download that which you need to get the system running in a stable
condition.

You need the latest Windows XP compatible chipset drivers. You need the
audio drivers - if you are using the onboard sound. You will need ethernet
drivers and modem drivers if you are using these devices.

The M/B is only USB 1.1 capable. To use USB 2.0 you absolutely need either
Windows XP SP2 or the Windows XP compatible drivers from the manufacturer of
the USB 2.0 add-in board you have installed. You can not plug in an external
USB 2.0 hub to an internal USB 1.1 connecter and expect to be able to use
USB 2.0.

I know that all of the above may not apply to you, so use what fits.

--
Regards,

Richard Urban
Microsoft MVP Windows Shell/User

Quote from: George Ankner
"If you knew as much as you thought you know,
You would realize that you don't know what you thought you knew!"

"Yabbadoo" <nospam@thank.you> wrote in message
news:teqDe.1416$Cu3.6@newsfe4-win.ntli.net...
> Since replying to last message, have found an ASUS VIA DDR chipset series
> "support" CD (in addition to the TARGA pc support CD) both of wh came with
> the original PC, some 3 + years ago. Have thoroughly searched this CD
> too - no mb manual, nothing relating to USB or chipset drivers
> Further - this PC (with XPHome pre-installed), but - not one of the
> support files on any of the CD's mention XP - all the drivers pre-date XP
> (are for W98 up to NT or 2000) so I would be reluctant to use these CD's
> as source for XPPro drivers.
> As far ASUS support is concerned - can get to the site via link
> http://usa.asus.com/aap/a7v266e-aa/overview.htm but that's as far as it
> goes - the overview only, further pages/downloads are just "not available"
> This actually replicates situation a year or more ago - had probs with the
> on-board CMI8738 sound, ASUS site then operated but was useless as far as
> updated drivers were concerned, none worked. Solved that prob by
> installing new sound card. Given both previous and current history, next
> time I upgrade it will not be an Asus m/b! I recall various forums
> discussing identical probs - all equally frustrated.
>
> Appreciate the advice, but alas! it's no good for Asus m/b's.
>
>
> "Colin Barnhorst" <colinbarharst@msn.com> wrote in message
> news:uPToIpOjFHA.1044@tk2msftngp13.phx.gbl...
>> All motherboards require reinstallation of the mobo chipset drivers after
>> a new installation of Windows. It is like needing to reinstall your
>> video card drivers. The usb2 card drivers on your cd are for versions of
>> Windows prior to XP SP1. They make no difference to XP SP1 and later
>> because they are built into the OS from SP1 on. Find the cd with that
>> came with the mobo or visit the manufacturer's site and download the
>> drivers and install them. There should be some useful utilities also.
>>
>> "Yabbadoo" <nospam@thank.you> wrote in message
>> news:ApdDe.3087$yH4.2017@newsfe2-win.ntli.net...
>>> Not sure what you mean about chipset drivers, but as stated I have (and
>>> used) the USB2 card installation CD.
>>> According to every diagnostic (System Manager, Belarc and Everest)
>>> there's no probs, every device is functionng normally. Also, I
>>> auto-update (SP2 installed months ago, and all later updates as
>>> released).
>>>
>>> I have a totally clean system, defended by AVG, MS antispyware latest
>>> beta, Spybot, Adaware, and daily clean/defrag by Tune-up Utilities
>>> schedule. I run total manual scans at least weekly, so, it ain't
>>> malware.
>>>
>>> PC is working fine on all apps/hardware - except USB2. Just installed
>>> new DVD_RW to replace DVD_R - that too working just fine.
>>>
>>> "Jerry" <NoSpamChiefZeke@MSN.com> wrote in message
>>> news:uOr9c7IjFHA.3656@TK2MSFTNGP09.phx.gbl...
>>>> When you reinstalled XP Pro did you install the chipset drivers for the
>>>> motherboard and the drivers for the add-in card?
>>>>
>>>> "Yabbadoo" <nospam@thank.you> wrote in message
>>>> news:gebDe.1291$Cu3.608@newsfe4-win.ntli.net...
>>>>> Help please - I'm going round in ever-diminishing circles here, almost
>>>>> disappearing up my fundamental you-know-what
>>>>> .
>>>>> My PC had 6 USB1 ports - I upgraded by adding a 2-port USB2 card, with
>>>>> a USB2 4 port hub ... When I had XP Home, all was fine. I then
>>>>> crashed my hdd, so bit the bullet, got a new drive, and XP Pro and
>>>>> started again.
>>>>>
>>>>> The (Via) USB2 card was bought new, as was the 4 port hub - I have the
>>>>> driver CD for the card.
>>>>>
>>>>> According to System Manager, everything's fine, working correctly.
>>>>> BUT - every time I try to use my USB2 memory stick in one of the 4
>>>>> ports on the hub, it comes up with "This would work faster with USB2 -
>>>>> put it in one of the 4 unused ports" .... which is unmitigated b/s as
>>>>> it's already IN one of them - changing makes no difference.
>>>>>
>>>>> I've already outed the 4 port hub in the belief it MIGHT be duff, got
>>>>> replacement - beggars belief that 2 sealed units are both u/s. Hub has
>>>>> external power, so it's not that either. It's driving me nuts - HELP
>>>>> !!!!
>>>>>
>>>>
>>>>
>>>
>>>
>>
>>
>
>

Archived from groups: microsoft.public.windowsxp.basics (More info?)

By chance, happen to have a friend who more than qualifies - he's stumped
too (similar advice - locate the drivers).
Thought I'd said (in another reply) that my pc is fully up-to-date with SP2
and later, and totally devoid of malware.

Given that, a year ago, Asus were unable to help with sound drivers, I
adjusted BIOS and Device Manager to de-activate on-board CMI8738 sound chip,
replaced with Audigy sound card. That prob.solved, no thanks to Asus.
(incidentally, most unusually, no-one could help in ng posting - sound probs
clearly not within this ng remit)

As far as LAN/ethernet is concerned - have 2 LAN cards, one, the cable
modem, the second, a 2 PC network - both work fine.
All kit installed/set up by me, with occasional ng help, which is most
appreciated.

I do have sufficient IQ to realise USB2 devices plugged into USB1 will
function at USB1 - if only that were the problem. it would be so simple to
rectify!
The problem is - USB2 card - with USB2/XP installation CD - will not
function at USB2 even though System Manager confirms the enhanced controller
is installed and working. (Applies to all devices - all OK, no conflicts).

Nor is it the fault of the USB2 4 port hub - same error occurs no matter
whether the device is connected to USB2 card direct or via the hub. The
killer is - the USB2 card/hub worked fine in XPHome! It's XPPro (or, the
combination of virgin hdd and XPPro installation) which first yielded the
problem.

"Richard Urban [MVP]" <richardurbanREMOVETHIS@hotmail.com> wrote in message
news:u6Ocg0RjFHA.2852@TK2MSFTNGP14.phx.gbl...
> Could you have reached that point where you should take your computer to a
> professional and allow them to straighten it out for you?
>
> I have one computer that uses an Asus A7V266E M/B. The M/B came with
> everything necessary to set up the computer, up to Windows 2000. Windows
> XP came out after the M/B was introduced. Of course you won't find what
> you need on the CD. You have to go to the various manufacturers web sites
> and download that which you need to get the system running in a stable
> condition.
>
> You need the latest Windows XP compatible chipset drivers. You need the
> audio drivers - if you are using the onboard sound. You will need ethernet
> drivers and modem drivers if you are using these devices.
>
> The M/B is only USB 1.1 capable. To use USB 2.0 you absolutely need either
> Windows XP SP2 or the Windows XP compatible drivers from the manufacturer
> of the USB 2.0 add-in board you have installed. You can not plug in an
> external USB 2.0 hub to an internal USB 1.1 connecter and expect to be
> able to use USB 2.0.
>
> I know that all of the above may not apply to you, so use what fits.
>
> --
> Regards,
>
> Richard Urban
> Microsoft MVP Windows Shell/User
>
> Quote from: George Ankner
> "If you knew as much as you thought you know,
> You would realize that you don't know what you thought you knew!"
>
> "Yabbadoo" <nospam@thank.you> wrote in message
> news:teqDe.1416$Cu3.6@newsfe4-win.ntli.net...
>> Since replying to last message, have found an ASUS VIA DDR chipset series
>> "support" CD (in addition to the TARGA pc support CD) both of wh came
>> with the original PC, some 3 + years ago. Have thoroughly searched this
>> CD too - no mb manual, nothing relating to USB or chipset drivers
>> Further - this PC (with XPHome pre-installed), but - not one of the
>> support files on any of the CD's mention XP - all the drivers pre-date XP
>> (are for W98 up to NT or 2000) so I would be reluctant to use these CD's
>> as source for XPPro drivers.
>> As far ASUS support is concerned - can get to the site via link
>> http://usa.asus.com/aap/a7v266e-aa/overview.htm but that's as far as it
>> goes - the overview only, further pages/downloads are just "not
>> available" This actually replicates situation a year or more ago - had
>> probs with the on-board CMI8738 sound, ASUS site then operated but was
>> useless as far as updated driver