RME ADI-8 Pro Mod?

G

Guest

Guest
Archived from groups: rec.audio.pro (More info?)

I was happy with my RME ADI-8 Pro for getting audio in and out of a
Digi 001 setup @ 44K untill I did an unscientific comparison of the
Kurzweil Rumour's A/D vs the RME's.

I prefered the Kurzweil's conversion.

I've heard of a modification out there for the RME. Anyone have this
work done? Pleasing results?

Thanks for any thoughts, Fingerz
 
G

Guest

Guest
Archived from groups: rec.audio.pro (More info?)

Fingerz88 <fingerz88d@aol.com> wrote:
>I was happy with my RME ADI-8 Pro for getting audio in and out of a
>Digi 001 setup @ 44K untill I did an unscientific comparison of the
>Kurzweil Rumour's A/D vs the RME's.
>
>I prefered the Kurzweil's conversion.
>
>I've heard of a modification out there for the RME. Anyone have this
>work done? Pleasing results?

Jim at Audio Upgrades has done a lot of things to the RME, including
using better op-amps and capacitors in them. I have only tried bypassing
some of the input capacitors but found that to be a definite improvement.
--scott

--
"C'est un Nagra. C'est suisse, et tres, tres precis."
 
G

Guest

Guest
Archived from groups: rec.audio.pro (More info?)

Scott Dorsey wrote:

> Jim at Audio Upgrades has done a lot of things to the RME, including
> using better op-amps and capacitors in them.

Based on some work using Kurt A's JW mod'd ADI-8 Pro DS I'd say Jim's
work is well worth the money.

--
ha
 
G

Guest

Guest
Archived from groups: rec.audio.pro (More info?)

Thanks folks.

You'd think RME would take note of these 3rd party upgrades and make
the product as good as it could be from the outset.

I wonder if the mod to the RME would have the unit yielding superior
results to the Kurzweil's conversion...?
Hmmm.....
 
G

Guest

Guest
Archived from groups: rec.audio.pro (More info?)

>And there are some converters out there that are probably
superior to the Kurzweil too.
--scott

Maybe, but I doubt it!
 
G

Guest

Guest
Archived from groups: rec.audio.pro (More info?)

You might want to watch out for that. Most modern A/D chip's inputs are
voltage referenced to 1/2 the power supply, at 2.5 volts. Blocking caps
are needed to keep this bias out of the input connectors and then out
of the device that's feeding it. Running 2.5 volts up the ass of a mic
pre may not cause a problem, but if it's direct coupled, or if the
coupling caps are reversed, it could be one.

The mods include Wima MKP-2 250 polyprop film cap bypasses on the
Panasonic FM caps which are replaced. The opamps are LM6172's.

Have fun, remember, they don't work if you let the smoke out!
 
G

Guest

Guest
Archived from groups: rec.audio.pro (More info?)

RME Adi-8Pro is a difficult item. Modifications are not easy because the
pads are very thin and narrow. If you are not very skilled in soldering, be
aware of that.

For Scott: did you really bypass the 2 input caps for each channel? I gotta
try that...

F.


"Fingerz88" <fingerz88d@aol.com> ha scritto nel messaggio
news:1118979621.456782.164320@g47g2000cwa.googlegroups.com...
> Thanks folks.
>
> You'd think RME would take note of these 3rd party upgrades and make
> the product as good as it could be from the outset.
>
> I wonder if the mod to the RME would have the unit yielding superior
> results to the Kurzweil's conversion...?
> Hmmm.....
>
 
G

Guest

Guest
Archived from groups: rec.audio.pro (More info?)

Fingerz88 <fingerz88d@aol.com> wrote:
>
>You'd think RME would take note of these 3rd party upgrades and make
>the product as good as it could be from the outset.

That would radically increase the cost. Remember, this stuff is built to
a price point.

>I wonder if the mod to the RME would have the unit yielding superior
>results to the Kurzweil's conversion...?

I don't know. And there are some converters out there that are probably
superior to the Kurzweil too.
--scott
--
"C'est un Nagra. C'est suisse, et tres, tres precis."
 
G

Guest

Guest
Archived from groups: rec.audio.pro (More info?)

Federico <plokmichael@tiscali.it> wrote:
>RME Adi-8Pro is a difficult item. Modifications are not easy because the
>pads are very thin and narrow. If you are not very skilled in soldering, be
>aware of that.
>
>For Scott: did you really bypass the 2 input caps for each channel? I gotta
>try that...

Yes, since it's _always_ being used with a preamp that has output blocking
caps anyway. No reason to put more caps in series.
--scott

--
"C'est un Nagra. C'est suisse, et tres, tres precis."
 
G

Guest

Guest
Archived from groups: rec.audio.pro (More info?)

Fingerz88 <fingerz88d@aol.com> wrote:
>>And there are some converters out there that are probably
>superior to the Kurzweil too.
>
>Maybe, but I doubt it!

Go out and listen to the Prism stuff, or the higher grade Lavry gear.
--scott

--
"C'est un Nagra. C'est suisse, et tres, tres precis."
 
G

Guest

Guest
Archived from groups: rec.audio.pro (More info?)

In article <d8uk05$e9g$1@panix2.panix.com>, kludge@panix.com (Scott Dorsey)
wrote:

> Fingerz88 <fingerz88d@aol.com> wrote:
> >>And there are some converters out there that are probably
> >superior to the Kurzweil too.
> >
> >Maybe, but I doubt it!
>
> Go out and listen to the Prism stuff, or the higher grade Lavry gear.
> --scott

Or dCS.

--
Regards,

Klay Anderson
http://www.klay.com
+801-942-8346
 

TRENDING THREADS