Your question

Connected to Wifi but does not Work

Tags:
  • Laptops
  • WiFi and Home Networking
  • Connection
Last response: in Laptop Tech Support
December 7, 2017 3:54:27 PM

My laptop was working fine until a few days ago, until it blue screened and restarted. Since then, it has been saying that it is connected to wifi, but Im not able to actually use it or load anything. However, I tried restarting it in safe mode with networking and it seemed to work fine there. Whenever I try to use the internet otherwise, it's able to work for less than a second before stopping again. Any thoughts? Thanks.

More about : connected wifi work

a c 1121 D Laptop
December 7, 2017 6:39:35 PM

Try this....

1. Go to "Control Panel".

2. Next go to "Network and Internet" and then "Network and Sharing".

3. Now click on "Manage Wireless Networks".

4. On this screen, remove all wireless connections by "right clicking" on it and select "Remove network" from the drop down menu.

5. After doing this, close the open windows and reboot the computer.

6. Once the computer is fully reloaded, scan for the "WiFi networks".

7. Click on the available network that you want to access and select "connect".

8. It takes a moment, but then you will be asked to give a password for your WiFi connection. Type in the password and click the "connect" button.

It should now be connected.

NOTE: If this doesn't work, you may want to reset your modem/router, and then once it is fully loaded again, repeat the above steps.

If this doesn't work, test seeing if your laptop will connect via Ethernet. If so, then your WiFi card may be going. You can either look to replace it/have it replaced, or get an external (plugs in via USB) WiFi card.


Another way to try it is to...

1. Go to "Settings".
2. Click on "Network & Security" and then click on "WiFi".
3. Now click "Manage known networks".
4. Select the WiFi connection you want to remove.
5. Click the "Forget" button.
6. After doing this, close the open windows and reboot the computer.
7. Once the computer is fully reloaded again go to "Settings".
8. Click on "Network & Security" and then click on "WiFi".
9. Now click "Manage known networks".
10. Click "Add a new network" and enter the network name.
11. Using the drop-down menu, select the "network security type".
12. Check the "Connect automatically" option.
13. Now check the "Connect even if the network is not broadcasting" option and click "Save".

Once you have completed these steps, whenever the device is within range of that particular network, it should automatically connect to it.
m
0
l
14 minutes ago

webworkings said:
Try this....

1. Go to "Control Panel".

2. Next go to "Network and Internet" and then "Network and Sharing".

3. Now click on "Manage Wireless Networks".

4. On this screen, remove all wireless connections by "right clicking" on it and select "Remove network" from the drop down menu.

5. After doing this, close the open windows and reboot the computer.

6. Once the computer is fully reloaded, scan for the "WiFi networks".

7. Click on the available network that you want to access and select "connect".

8. It takes a moment, but then you will be asked to give a password for your WiFi connection. Type in the password and click the "connect" button.

It should now be connected.

NOTE: If this doesn't work, you may want to reset your modem/router, and then once it is fully loaded again, repeat the above steps.

If this doesn't work, test seeing if your laptop will connect via Ethernet. If so, then your WiFi card may be going. You can either look to replace it/have it replaced, or get an external (plugs in via USB) WiFi card.


Another way to try it is to...

1. Go to "Settings".
2. Click on "Network & Security" and then click on "WiFi".
3. Now click "Manage known networks".
4. Select the WiFi connection you want to remove.
5. Click the "Forget" button.
6. After doing this, close the open windows and reboot the computer.
7. Once the computer is fully reloaded again go to "Settings".
8. Click on "Network & Security" and then click on "WiFi".
9. Now click "Manage known networks".
10. Click "Add a new network" and enter the network name.
11. Using the drop-down menu, select the "network security type".
12. Check the "Connect automatically" option.
13. Now check the "Connect even if the network is not broadcasting" option and click "Save".

Once you have completed these steps, whenever the device is within range of that particular network, it should automatically connect to it.


If you haven't already check to make sure you pc is getting an ip or if your wifi is "Connected but limited" or "Connected, No Internet". And try pinging to googles dns too 8.8.8.8. If that fails, you can to a trace route to see where the connection stops.
m
0
l
Related resources
Tom’s guide in the world
  • Germany
  • France
  • Italy
  • Ireland
  • UK
Follow Tom’s guide
Subscribe to our newsletter
  • add to twitter
  • add to facebook
  • ajouter un flux RSS